FD20

Anodized aluminum or polycarbonate continuous cover profile (1.9 meters). Protects operator drive assembly and arm linkage from dust, debris, and tampering.

Modified 105 sliding rod for direct mounting to FD20 door leaf profiles. Enables integrated mechanical coupling in limited-space leaf-mount configurations.

Combined safety kit with 350mm and 700mm infrared 4SAFE units. Used where varied coverage is needed at top/bottom of the door leaf.

Sensor kit combo including both 350mm and 900mm 4SAFE modules. Allows tiered safety zones for advanced swing door applications.

Compact 350mm-range sensor kit for swing doors. Ideal for narrow leaf or limited field of detection requirements.

Medium-range swing door safety sensor kit (700mm). Balances range and compact form factor.

Dual-sensor 4SAFE safety kit (900mm range), black finish, for swing doors. Provides infrared presence detection to meet EN 16005 standards.

High-range (900mm) presence and motion sensor for swing door edges. Infrared curtain pattern ensures accurate obstruction detection.

12mm shaft extension for adjusting spindle-arm interface length. Used to fine-tune drive rod positioning or accommodate offset leaf hardware.

20mm extension for drive spindle. Useful in adjusting for custom leaf depths or non-standard mounting conditions.

Intermediate 30mm axle extender; balances reach and torsional stress. Designed for installations where mounting offset needs to be bridged.

Long-format 40mm extension piece for motor output shaft. Ensures proper articulation in extended-leaf setups.

Maximum-length (50mm) spindle extension; for deep-profile doors or when mounting point is set back from spindle axis.

3.2-meter CAN bus communication cable for connecting various control modules and sensors within the Gilgen automation network. Shielded to prevent signal interference.

Primary mechanical retainer for rods or arms; secures to sliding channel or output shaft. Precision-machined for torque load retention under dynamic conditions.

Clamping spacer with 20mm extension. Compensates for non-standard mounting geometries or wider leaf profiles. Maintains correct mechanical alignment of the drive rod.

Extended version of clamping spacer (+50mm). Suitable for deep-profile doors or custom header/leaf interface situations.

Short-profile variant of standard clamping piece. Used in compact installations or where reduced axial protrusion is necessary.

Digital access control module for Gilgen door systems. Integrates with FD20 via secure I/O for entry management.

Complete D-Bedix access unit with flush-mount back box. Weather-resistant housing and prewired for direct integration with door controller.

Spacer used to align sliding rod within drive channel. Ensures correct contact and avoids mechanical play or misalignment.

Digital control module for FD20 operator. Manages motor control, I/O with safety and activation sensors, CAN communication, and programmable logic routines (e.g., delay, speed, hold-open).

High-efficiency DC gear motor for the FD20 swing door system. Delivers reliable torque output under continuous-duty cycles. Integrated with encoder feedback for position control.

End cap for FD20 side cover; secures the longitudinal cover rail and ensures clean termination. Helps maintain IP rating and visual finish.

Full enclosure cover set for FD20 drive unit. Includes mounting clips and seals. Provides protection against ingress (dust, accidental contact). Aesthetic finish.

Gliding element designed for RG-type sliding rod assemblies. Provides low-friction linear movement along the track, ensuring smooth articulation during opening and closing cycles.

Reinforcement plate installed behind primary components (motor, control) for mechanical load distribution. Provides secure anchor point in wall or header frames.

RS-oriented stop insert for precise control of the door’s open position. Ensures consistent end-of-travel limit on right-hand swing doors.

Mechanical stop that defines the fully open travel limit of the door. Installs in the slide rail to prevent over-travel and safeguard drive gear integrity.

RG-type sliding rod for pull-arm setups, specifically for right-opening inward doors. Sliding feature reduces wear in high-cycle applications.

Standard-length drive arm rod used in push arm configurations. Transfers torque from drive spindle to door leaf for outward-opening systems. Designed for robust mechanical interface with clamping hardware.

Right-hand standard rod for push arm configurations (RS-type). Ensures correct door swing in right-opening installations.

Sliding drive rod for pull arm installations. Allows axial movement during opening/closing cycle. Optimized for inward-opening doors, reducing resistance and stress on the door leaf.

Travel limit stop for RG-type pull arm configuration. Aligns with sliding track to ensure repeatable stop behavior.